PHYSICAL AGREEMENT
TITLE 601 - GAS DEPARTMENT
Section 601.5 Gas Measurement and Control
Section | Date | Description |
---|---|---|
PRC 21774 | 6/2/2014 | Gas Operations-Gas Control: Case concerns whether a work assignment for a Relief Gas System Operator was an assignment under the Relief Agreement or an emergency overtime assignment. Based on Relief Agreement Grievant had not started working the first assigned relief shift for that week and therefore was available to be reassigned. |
LA R2-13-67 | 9/24/2013 | Proposes the establishment of two new LNG/CNG Operations classifications: Senior LNG/CNG Technician and LNG/CNG Technician. |
LA 13-61 | 7/25/2013 | Given the required timeframe for completing atmospheric corrosion inspections work and the existing workload being performed by regular employees, which includes working overtime, the Company proposes utilizing contractor resources signatory to Local 1245 to perform this work during regular work hours through September 2013. The Company agrees to continue to offer optimum overtime during this period (a minimum 20% overtime) for the appropriate classifications in the headquarters/service territory while the contractors are performing the applicable work within the work area |
LA 13-48 | 6/19/2013 | To update SAP with the correct wage rates of Lead Gas Control Technician (2434) and Lead Gas Transmission Technician (2416) for 2013 as soon as possible. Exhibit X corrections will be updated as soon as practicable. |
LA 12-45-PGE | 10/17/2012 | Adjust job duties and wages of the following classifications: (2410) Gas Control Technician; (2435) Gas Control Technician-GSM &TS; (2442) Gas Control Technician COGEN; (1365) Measurement and Control Mechanic; (1366) Un Measurement and Control Mechanic; and (1245) Corrosion Mechanic. This LA cancels and supersedes LA-11-47-PGE. |
P RC 20943 | 10/16/2012 | Assignment of a Corrosion Mechanic to perform gas stand-by duties. Agrees that CM may also perform these duties provided they are properly qualified. |
LA 05-51 | 10/6/2005 | Revised Corrosion Mechanic Training Program (Administrative Procedures Manual, Aug. 12, 2005). |
LA 03-18 | 6/11/2003 | To establish Utility Field Clerk SF 0248, with a single rate of pay of $997.65 per week. |
LA 01-30 | 7/27/2001 | Revised JDLOP for the Title 200 Gas Measurement and Corrosion Control. |
LA 01-15 | 4/5/2001 | Gas Operator Qualification Plan which outlines the Companys responsibilities and procedures to ensure that it has a qualified workforce and that its operations comply with relevant Federal Pipeline Safety Regulations. |
LA 97-13 | 2/12/1997 | As a result of (LA 96-44) combining Region Gas Control Operator and Gas Supply Coordinator classifications, the Company established Gas System Operator - M&C (PIO), classification code 1593. See also 204.4 and 604.3. |
LA 97-06 | 1/8/1997 | Training program for the Gas System Operator classification and Gas Operator-in-Training classification. See also 109.2 and 604.3. |
LA 96-44 | 6/10/1996 | To combine the classifications of the Regional Control Operator (1579), Gas M&C and Gas Supply Coordinator (1836), GT&S to a Gas System Operator (1587) classification in the Gas Trans. & Storage LOP. In addition, to establish a Gas Operator-In-Training (1588) classification in the GT&S LOP. See also 205.19, 206.8, 206.12, 204.4, and 604.2. |
LA 96-09 | 2/5/1996 | To modify the proposed changes to the 50-day Corrosion Mechanic course for the Div. Gas Measurement and Control Group. See also 10.2 and 205.19. |
RC 1723 | 1/4/1996 | Issue of Gas M&C and PLO employee required to perform duty of higher classification settled by establishment of Gas Control Technician and Apprentice. See also 604.4. |
P-RC 1764 | 9/22/1995 | Training a non-welding M&C Mechanic to weld is a violation of agreement. |
LA R2-93-55 | 3/8/1994 | Updates of JDLOP - Division Gas Measurement and Control; replacing LA 85-15. |
LA 93-29 | 5/27/1993 | Reclassify the position of Gas M&C Mechanic to a Gas Control Technician in Diablo Division. See also 204.4 and 205.19. |
LA 92-127 | 9/16/1992 | Filling of Gas Control Technician positions at Merced. See also 205.19. |
LA R1-92-97 | 9/4/1992 | Established Ad Hoc Technology Committee to collaborately examine issues surrounding technological advances in the workplace. See 601.1, 204.4, 603.1, 612.3, and 612.4. |
LA 92-116 | 8/10/1992 | (Gas Operator in Training) GOIT Training Program. See 205.13. |
LA 92-99 | 7/8/1992 | Reclassifying an M&C Mechanic to a Gas Control Technician at Sacramento Div. See also 205.19. |
LA 92-86 | 6/11/1992 | Placement of employee into Gas Control Technician position at Marysville. See also 205.19. |
LA 92-76 | 5/26/1992 | Wage rates for Gerber Gas Supply Business Unit employees. See also 204.4. |
LA R3-91-145 | 5/8/1992 | Transfer of employees from Gas M&C to Gas Transmission and Storage (formerly PLO). See also 205.19, 206.15, 206.18, 604.2 and Clerical 18.17. |
LA 92-7 | 1/21/1992 | Reclassification of Measurement & Control Mechanic, Sacramento. Load Station to Gas Control Technician; new Gas SCADA and electronic systems require higher classification for more technical nature of work. See also 204.4. |
LA R1-91-160 | 11/27/1991 | Reclassification of three Measurement & Control Mechanics at Fresno Service Center to Gas Control Technicians. More technical nature of work associated with new Gas SCADA system requires the higher classification. See also 204.4. |
LA 91-10 | 1/11/1991 | Reclassification of two Measurement & Control Mechanics at Region Gas Load Center-Fresno, to Gas Control Technicians. More technical nature of work associated with new Gas SCADA system requires the higher classification. See also 204.4. |
LA 90-196 | 8/29/1990 | Some mark and locate duties normally performed by Fieldmen may be handled under certain circumstances by one Corrosion Mechanic in Eureka, Humboldt Division. Number of Fieldman positions in Eureka will not be reduced. See 601.1. |
LA 90-116 | 5/15/1990 | Eureka Gas Load Center to convert from 24-hour operation to 16-hour operation (see LA 89-9, this section). Outlines staffing and rotational shift assignments. See also 202.16, 601.4. |
RC 1669, 1678 | 1/12/1990 | Guidelines concerning appropriate bargaining unit classifications to handle personal computer repair and maintenance, telephone station moves, adds and changes. See also 2.1, 603.2, 603.4, 612.4. |
LA 89-162 | 9/6/1989 | In relocation of 11 employees from Gas Transmission and Regulation Department, Marysville to Gas Collection Department, Meridian, no changes in 208.16 to be implemented. However, should additional personnel be needed for POT, Marysville will be contacted prior to other gas collection or Pipe Line locations or other Divisions. See also 206.8, 206.9, 206.12, 208.16, Clerical 19.9 and 19.12. |
LA R3-88-110 | 1/19/1989 | Clarification of Title 206, Demotion and Layoff Procedure. Also includes reverse lines of progression for Gas Measurement and Control Group, and Gas Measurement and Control Operating. See Title 206 Clarification, 601.1, 601.4, 603, 609.1, 612.1, 612.2, 612.5. |
LA 89-9 | 1/9/1989 | Conversion of Eureka Gas Load Center to 24-hour dispatch operation. For this agreement only, duties of Pressure Operator and System Operator will be the same, and Relief Pressure Operator will provide relief for both. If operational needs dictate additional relief, Humboldt Division Gas Serviceman may be used. See also 202.16, 205, 206, 601.4. |
LA 85-15 | 2/7/1985 | Revision of Gas M&C Lines of Progression. |
P-RC 954 | 7/13/1984 | Employees have preferential consideration to return to position from which they were demoted, if they have not removed themselves from LOP of classification to which they were demoted. Corrosion Mechanic demoted to Field Meterman, bid to Pressure Operator which is in LOP to Field Meterman, thus keeping 206.9 rights back to Corrosion Mechanic, even though Pressure Operator is no longer in LOP to Corrosion Mechanic. See 206.9. |
LA 84-72 | 6/13/1984 | Establishes 1247 Lead Compressor Mechanic (Rio Vista, Sacramento Division only) with job description, line of progression, wage rate, academic, technical and mechanical requirements. |
P-RC 892 | 12/22/1983 | It is within the job definition of Corrosion Mechanic to install, check, adjust, operate and maintain all types of corrosion control equipment and instrumentation, including internal corrosion inhibitor pumps. |
P-RC 829 | 9/15/1983 | Bypass by junior, but qualified, employee in temporary upgrade to Corrosion Mechanic justified. Grievant was not qualified because Company has not offered Corrosion Mechanic training course for two and one-half years. In future, course will be given annually. See 205.11 and 604.5. |
LA 83-7 | 2/15/1983 | Adds 1414 Unassigned Transmission Mechanic same or higher to 1245 Corrosion Mechanic line of progression. |
Local Agmt. San Jose Div.& Union | 10/19/1982 | Effective 11-1-82, San Jose Division Gas M&C will be divided into two districts, Central and DeAnza. Four M&C Mechanics, three Corrosion Mechanics and ten Gas T&D Helpers assigned to San Jose M&C group will be relocated to DeAnza District. See 206.17. |
RC 1534 | 8/26/1982 | In dispute over Gas Meter Repair Plant or Field employees doing work, it was decided that it is within the job definition of an M&C Mechanic and/or Fieldman under the direction of an M&C Mechanic to repair and stock 3/4" K-type regulators. See 601.1 and 601.3. |
RC 1525 | 2/11/1982 | Gas Mechanic's setting gas meters over 300 cubic feet per hour is accepted in some areas. Decision lists conditions under which Gas Mechanic may place meter in service and rate of pay he shall receive when so upgraded. In this case, as an equity settlement, Gas Mechanic was upgraded to Gas M&C Mechanic. See 601.1. |
P-RC 657 | 11/9/1981 | Under these circumstances not appropriate for Corrosion Mechanics to do Serviceman's work. See 601.4. |
LA 81-73 | 6/19/1981 | Updates job definitions and lines of progression for Division Gas Measurement and Control group. Includes comparable GC jobs which were transferred from Exhibit VIII to the Division lines of progression. |
RC 1511 | 3/4/1981 | Agreement is not violated by Company's revising Corrosion Mechanic audit system, designed not for discipline, but to evaluate proficiency, safety practices, and adequacy of training. Audit will be reviewed and discussed with employee who may obtain a copy upon written request. Failure to meet the revised standard of achievement is not just cause for discipline. See 7.1. |
P-RC 573 | 1/13/1981 | Obtaining water samples for observation by supervisor and taking readings in order to determine if corrective steps are needed is within job definition of Corrosion Mechanic. |
RC 1492 | 10/1/1980 | In the Peninsula District of the San Jose Division it is the long-standing practice to assign installation of meter sets over 300 cubic feet capacity to Gas Mechanics. If any malfunctions are observed the meter is to be turned off, and the appropriate M&C classification called. See 601.1. |
LA 79-35 | 4/13/1979 | Changes resulting from Oakland Gas Holder Station's going on standby status. Outlines changes at Oakland, Richmond and 50th Ave., with vacation schedules. |
LA 78-76 | 12/21/1978 | Permits Gas Service Operators and Relief Service Operators to man Gas Load Center and perform Pressure Operator job duties. See 601.4. |
LA 2182 | 7/8/1977 | Revision of Corrosion Mechanic Training to include basic math as pre-requisite. See 604.5. |
LA 2243 | 2/4/1977 | Revises Corrosion Mechanic job definition and rates of pay and establishes same in Pipeline Operations. See 604.5. |
P-RC 253 | 1/4/1977 | Unresolved difference between Pressure Operators and Service Operators regarding call-outs in Marin District Gas Service Department. See 212.1 and 601.4. |
RCs 1185 & 1186 | 12/10/1975 | When employees perform work previously performed by Light Crew Foremen, they are entitled to upgrades to Gas Control Technician. See 601.1. |
LA 1067 | 6/20/1974 | Pressure Operators at San Jose, Eureka, Marysville, Sacramento, and Oakland have bidding rights to Corrosion Mechanic classification. |
P-RC 80 | 6/18/1974 | It is within the job definitions of Communication Technicians and Gas Control Technicians to maintain certain communications equipment at Marysville Substation; however, grievance not timely filed. See 102.3. |
P-RC 26 | 5/14/1974 | In case involving question of whether work belonged to Gas M&C Mechanic or Gas Control Technician, the job replacement of the time delay relay and scanner switch in the unit did not involve transistorized circuitry, so it was not Gas Control Technician work. |
LA 1021 | 2/19/1974 | Former ESC Chemical Assistant placed as Routine Chemical Assistant, incumbent only, with training program tailored to his experience and background. |
RC 1315 | 2/7/1974 | Division should assign proper classification to perform annual pressure verification and pay accordingly. Field Meterman may perform routine metering pressure verifications, but higher classification required to adjust regulator. |
RC 1111A | 1/23/1974 | Gas Measurementman working on calorimeter: settled by 1972 negotiations with establishment of Apprentice Measurement and Control Mechanic and Orifice Meterman. Gas Measurementman classification eliminated. |
LA 983 | 10/3/1973 | Revises some lines of progression, Gas Measurement and Control. See 609.1, 613.1, and 613.2. |
LA 955 | 7/26/1973 | Training requirements for former ESC Gas Instrument Technicians transferring to IBEW as Gas Measurement and Control Mechanics. |
LA 929 | 5/1/1973 | Transfers ESC Gas Instrument Technician into IBEW as Measurement and Control Mechanic. See 603.5. |
LA 833 | 11/3/1972 | Job definitions, wage rates, lines of progression, Gas Measurement and Control. |
LA 862 | 9/28/1972 | Establishes Plant Helper classification. |
LA 830 | 6/25/1972 | Entrance requirements for Corrosion Mechanic Training School and guidelines for temporary upgrades. See 604.5. |
LA 868 | 6/25/1972 | Guidelines for Apprentice Gas Measurement and Control Mechanic training program. |
RC 1014 | 11/16/1970 | Apprentice Gas Measurementman performing Field Meterman work will be paid as Field Meterman for that time. |
LA 283 | 5/28/1968 | Agreement with respect to the filling of three Apprentice Gas Measurementman classifications in Stockton Division. |
LA 160 | 7/28/1967 | Agreement establishing the operating conditions and exceptions to the relief policy for the Oakland Holder Station, the 50th Ave. Holder Station and the Point Richmond Holder Station. |
LA | 3/6/1956 | Abolish First Operator at Station B, Humboldt Bay Steam Plant and establish First Operator, Sched. I and Watch Engineer classifications. |